Worm drive gearbox with motor
A robust worm-drive gearbox powered by an MM28 engine. Ideal applications where an easy to fit, high torque end result is required. Ideal for student based projects including robots and buggies.
The unit has been designed to ensure that the output shaft can be ‘clicked’ in and out for modification. Electronic.g. reducing to size. The engine is snap fitted into its cradle to engage the gear and worm.
1 – 6V DC
0.1A to 1A depending on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + motor: 35(W) x 40(H) x 60(L)mm
The primary feature of this high-efficiency gear box is a worm gear, which locks the output shaft whenever the motor isn’t turning. The high equipment ratios of 216:1 or 336:1 make this gearbox appropriate for small strolling robots, lifting mechanisms, and various other applications where great torque is desired.
The low-voltage motors in the worm gearbox operate on 1.5-4.5 volts and draw up to some amps, making them ideal applicants for the DRV8833 motor driver carrier. Electric motor overheating can be caused by excessive stalling, even at suprisingly low voltages. We advise that you use stall-detection sensors, or simply look at your robot, to make sure that it doesn’t stall for lots of seconds at a time.
This gearbox includes a 4 mm diameter, round output shaft, which works together with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal installation hub also fits on the smaller threaded end of the shaft, although it is not specifically intended to work with this type of shaft (the hub’s set screw could harm the thread on the shaft).
Ever-Power gear motors will be economical, right-angle, worm-geared motors that install easily found in the tightest applications. Economical correct angle worm geared motors set new standards for reliability, performance and economic climate with unparalleled features which includes hollow shafts in the tiniest sizes. An inverter friendly style offers easy integration at this point and a really future proof remedy. The Ever-Power gear electric motor offers total flexibility in mounting options includes shaft, base, encounter, and flange alternatives. The motor terminal box could be mounted in alternative positions rotated in 90º steps around the electric motor frame providing for unparalleled integration options.
Ever-Power gear motors adhere to North American and International specifications, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a genuine total option for our global customers.
Excellent protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dirt tight and hose proof,and can be utilized outdoors or in wet and dusty conditions without the use of additional enclosures. Complete rated output is offered by the output shaft of the machine.
Power ranking up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Completely enclosed, sealed against dust and water spray
Lubrication change first after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Regular), IP66 (Optional)
Connecting with Connect connectors.
With integrated inverter up to 7,5kW.
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the option for applications requiring a good part turn, optional dual result, or perhaps an inability for the electric motor to be back driven. The DC correct angle equipment motors are made for constant and intermittent duty procedure. Our right angle equipment reducers are designed with a number of mounting plate options, making them ideal for a number of DC engine based applications. We offer 12 ratios which range from 5:1 to 100:1.
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ time (varies by application)
EP Products Worm Gear Motors are created to generate high torque in a little package size. Worm Equipment Motors are excellent for applications that require a self- locking or breaking feature since the output shaft can’t rotate when there’s no power applied. On top of that, Worm Gearheads can transfer motion in 90 degrees. With various decrease ratios, precision cut gears, voltages and sizes, EP Items includes a DC Worm Equipment Motor solution for the application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Gear Reduction Ratios
Security Door Locks / Industrial Conveying Systems / Security Gates / Dental care Seats / Ambulance Cots & Stretchers Quite a few DC Motors could be complimented with one of our Worm Gearheads. EP Products will work with you to create and produce a Worm Gear Motor that may optimize the performance of your specific application.
Built to your unique requirements
Electric motor Type: Brushed / Brushless / Coreless
Shaft Material & Size
Shaft Configuration: (D Trim / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Additional Assembly Requirements (lead wires, connectors, etc.)
The turbo metal gear worm motor uses a metal gear box for durability and a higher torque output. Because of the special mechanical framework of the worm travel the electric motor output shaft can be self locking and will not be rotated.
This part uses a two wire connection and supports direction control as well as PWM speed control. Ranked voltage is 12v and will obtain 40RPM, with a torque of 8kg/cm.
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Ranked Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear models from EP DRIVESYSTEMS especially show their power in applications where large gear ratios are necessary. Our worm geared motors happen to be therefore optimally suited for use in intralogistics, packaging technology and the food & beverage industry.
Four great reasons for EP worm geared motors:
Our worm geared motors have a higher overload capacity
Washdown versions allow simple and efficient cleaning of the travel system.
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Our modular style give users maximum freedom.
The modular system for optimum flexibility: Our EP worm gear units
There are many applications that require drive systems, and each of these has its own unique requirements. The EP series worm equipment motors can be quickly and efficiently adapted to satisfy your needs.
Worm gear units impress with their great power density and small style. If required, we are able to also source them with the highly effective nsd tupH surface area treatment.
As well as the basic EP casing, we offer an extensive type of bolt-on parts to customize the merchandise including torque arms, shaft covers and output flanges. These could be easily field set up, but we may also be pleased to assemble the individual components for you.
Find out more about our modular SI worm geared motors!
Find out more
Smooth and Clean: The EP worm gear unit SMI
SMI worm gear units feature a smooth, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface area conversion makes the product preferably suited for harsh and demanding industries like food processing and pharmaceuticals.
Flexible input designs such as for example NEMA, IEC or direct motor mounts in extra foot or flange mounted casing designs.
Worm geared motors
Worm geared motors for small power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared motor program. The units possess on all sides diverse fixing possibilities and enable a simple assembling for the client.
Other drive configurationscan be designed by use of built-on components (e.g. torque arm and output flanges). The housings are created in light weight structure out of aluminium die cast. Engine attachment is realised in general by way of IEC adapter B5 or B14A.
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/installation:uniblock, flange, torque arm
Buy Worm Drive Gearbox with Engine – incorporating the following features: 1 to 6V voltage ranking, 17100 rpm simply no load speed, 220g-cm stall torque, 3mm shaft diameter, 60mm long, 35mm huge, 40mm high, a good robust worm get gearbox powered by an MM28 electric motor (included), most suitable for applications where a simple to match, high torque outcome is necessary, nylon housing and gear, requires light oil or silicon grease lubrication, well suited for student based tasks including robots and buggies.
Most suitable for applications where a simple to match, high torque output is required
Perfect for student based projects including robots and buggies
Reversible Great torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Reversible Excessive torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
The motor is Gear DC motor with micro-turbine worm, you can change the wiring-connection to change motor rotation.
Turbo worm geared motor with self-lock, that is, regarding motor without electrical, the outcome axis is definitely fixed, self-lock.
The reducer output shaft arranged vertically with the motor shaft, whole motor output shaft relatively-short than general gear motor, trusted to be installed the dimensions requirements strictly occasion.
No load speed: 40r/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Application: open the windowpane, door, Mini winch. Ect.
In sumo robot or combat robot competition where huge holding torque’s engine is essential in order to avoid your robot being pushed by your opponent robot. The worm equipment is definitely an improved option compared to the spur gear motor. How come worm gear so special? Check this wiki out: Worm Get.
“Unlike with ordinary equipment trains, the direction of transmission (insight shaft vs output shaft) isn’t reversible when using large reduction ratios, due to the increased friction involved between the worm and worm-wheel, when usually an individual start (1 spiral) worm can be used. This can be an advantage when it is desired to remove any likelihood of the output driving the input.”
In other phrases, it is difficult to push your load (example, your robot) if the motor isn’t power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking because of the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Worm drive gearbox with motor